How to DIY Container Storage Cabinet. You can finish it in 1 day!

Here is a new idea from Familyhandyman. A new model of storage cabinet that can allows you to tidy all the kitchen container.

Our sample 24-in. base cabinet required a 4 x 4-ft. sheet of 1/2-in.-thick plywood for the rollout, plus a 2 x 3-ft. scrap of 3/4-in. plywood for the carrier. Your container storage cabinet may require more or less.

The carrier fits under the rollout and isn’t very conspicuous, so almost any flat piece of 3/4-in. plywood will work for that.

In addition to the lumber, you’ll need a pair of 22-in. full-extension ball-bearing slides. (We suggest that you can choose the soft close drawer slides or push to open drawer slides)

We used a table saw to cut the plywood parts, but if you’re careful to make accurate cuts, a circular saw will work. You’ll need a jigsaw with a plywood-cutting blade to cut the curves on the sides and dividers. We used a finish nail gun and 1-1/4-in.- long brad nails to connect the parts, but you could substitute trim-head screws if you don’t mind the larger holes they leave.

1. Measure the opening of the base cabinet

Most base cabinets are about 23 in. deep and will accommodate this container storage cabinet rollout, but measure yours to be sure. If the measurement from the back of the face frame to the back of the cabinet is less than 22 in., you’ll have to build a shallower rollout and use shorter drawer slides.

The other critical measurement is the width. Measure the clear opening width; that is, the width from any protruding hinge or door parts to the opposite side of the cabinet opening (Photo above). Subtract 3 in. from this measurement to determine the width of parts B, C, D and E (as seen below in Project file — Figure A).

2. Cut the side panels

After adjusting the size of parts B, C, D and E for the container storage cabinet width, you can cut out all the parts except the carrier bottom. If you’re using a table saw, make partial cuts to form the L-shaped sides. But remember, you can’t see how far the blade is cutting on the underside, so be sure to stop short of your inside corner marks by at least an inch. The photo above shows how to complete the cut with a jigsaw.

3. Cut the curves

Trace along the edge of a 1-gallon paint can to draw the radius for the curve on the side panels. Trace along a quart size can to draw the radius on the dividers. Cut the curves on the sides and dividers with a jigsaw. Smooth the curved cuts with 100-grit sandpaper.

4. Assemble the rollout

Mark the location of the 1/4-in. rod on the side panels using Figure A (in Project file below) as a guide. Wrap tape around a 1/4-in. drill bit 1/4 in. from the end to use as a depth guide while drilling. Drill 1/4-in.- deep holes at the marks. Use a hacksaw to cut an aluminum rod 1/2 in. longer than the width of the bottom.

Apply wood glue to all edges that meet, and arrange the sides, bottom, front and back on a workbench and clamp them together. Work the aluminum rod into the holes. Tap the parts with a hammer to align the edges perfectly before connecting them with brad nails. Take your time aiming the nail gun to avoid nail blowouts.

5. Nail the dividers to the shelf

Finish the rollout by adding the dividers. First, decide how many dividers you want and calculate the width of the space between the dividers. Cut a spacer block to that dimension and use it as a guide to install the dividers. Attach the dividers to the shelf.

6. Nail the dividers to the rollout and cut carrier

Then measure down 7-1/2 in. from the top and make marks to indicate the top edge of the divider shelf. Line up the divider assembly with these marks and nail it in. Draw divider center lines on the  back of the rollout as a nailing guide. Then attach the dividers.

Drawer slides require 1/2-in. clearance on each side, so making the carrier exactly 1 in. wider than the rollout will result in a perfect fit. Measure the width of the completed rollout and add exactly 1 in. to determine the width of the carrier bottom. Cut the carrier bottom from 3/4-in. plywood. Then screw the carrier sides to the carrier bottom to prepare the carrier for mounting the drawer slides.

7. Screw the drawer slide to the rollout

Follow the instructions included with your drawer slides to separate the slides into two parts: a channel and a rail. Usually, pressing down on a plastic lever releases the parts and allows you to separate them. Screw the rails to the drawer.

8. Screw the drawer slide channel to the carrier

Rest the drawer slide channel on the carrier and align the front flush to the front of the carrier side. When you’re done installing the slides, check the fit by carefully aligning the rails with the channels and sliding them together. The rollout should glide easily on the ball-bearing slides. If the slides seem too tight, you can adjust the fit by removing one of the carrier sides and slipping a thin cardboard shim between the carrier side and carrier bottom before reassembling them.

9. Install the carrier

The photo above shows fitting the carrier assembly into the cabinet. There will be a little side-to-side play, so you can adjust the position to clear the hinge and door. This will probably require you to offset the carrier slightly away from the hinge side.

10. Install the rollout

Screw the carrier to the bottom of the cabinet and you’re ready to install the rollout (Photo above). Since you’ve already checked the fit, it should operate perfectly. Now load it up with containers and lids and enjoy your neatly organized container rollout.

Detail File

Materials list

You may interesting

(1) How to install a new kitchen sink? 6 easy steps with photos

(2) How to replace your old sink? Easy step by step with photos

(3) How to select a good kitchen sink? (1) – Sink material

(4) How to make a better use of your kitchen cabinet?

TAGS: ALLPRODUCT

Leave a Comment